Erfurt MAV

01427 616597
enquiries@erfurtmav.com

Wallrock Thermal Liner Adhesive

thermal_thermal_adhesive_885341738


Wallrock Brochure DownloadA high strength water based adhesive especially formulated for Wallrock Thermally efficient wallpapers, Polystyrene insulation products, PUR sound insulation and latex sound insulation. Easy roll formula for quick and easy application directly to the wall using a roller or brush. Available in 5kg or 10kg tubs. Typical consumption of 2m² to 1.5m² per kg.

  • High performance aqueous adhesive with fillers
  • Thick, smooth, low splatter formula - roll or brush straight from tub
  • High wet tack to hold while cutting and positioning
  • High resin content for optimum adhesion to surface
  • Allows walls to breathe and resists moisture
  • Contains an inhibitor to prevent mould, yeast and fungal growth

Can be used to hang:

  • Wallrock Thermal Liner KV600
  • Wallrock Thermal Liner
  • Wallrock R300 Cosy Liner
  • PUR Sound Insulation
  • Insulating Lining Paper
  • Insulating Lining Graphite+
  • Latex Sound Insulation
  • Heatsaver Wall Underliner

Before Use

This product is ready-mixed and ready to use, however some storage conditions may contribute to separation of water, visable on top of the product. This can be easily stirred into the bulk of the product without effecting the performance properties of the product. Despite stringent quality assurance procedures, defects may occur in exceptional cases from time to time. If a fault is found, please return any defective material to the place of purchase. Please see wallpaper roll labels for hanging instructions for each individual lining system.

Surface Preparation

Wallrock Thermal Liner Adhesive can be used on most internal wall surfaces. The adhesive contains filler and can be used in conjunction with our wallcovering products to cover surface imperfections and textures. All surfaces should be firm, dry and clean, all loose material should be removed before the adhesive is applied. Major surface imperfections should also be filled and levelled in preparation. Drywall and other absorbent surfaces should be sized and completely left to dry for at least 4 hours before application of the adhesive.

How Much Do I Need?

Each adhesive container holds 10kg (22lb), sufficient for 1 roll of Wallrock Thermal Liner KV600, 2 rolls of Wallrock Thermal Liner or 3 rolls of wallrock R300 Cosy Liner. Where the surface being covered is flat and in relatively good condition coverage will improve significantly by up to 25%. See guidance chart for other products.

Adhesive Application

The room temperature and that of the adhesive should not be less than 10°C/50°F. Please keep the adhesive sealed when not in use.

  • Generously apply the adhesive directly to the wall using a deep pile roller, use more paste if the wall is textured or damaged.
  • Apply adhesive to an area a little wider than for one length, this will ensure an adequate area is covered and make the next length easier to apply.
  • In the areas which the roller cannot reach, such as corners, the paste should be applied with a spatula or brush.
  • Each length of wallcovering should be butt jointed. Remove excess glue immediately with a damp cloth or sponge.

Drying Time

Drying time depends upon room temperature, humidity, thickness of the paste layer and surface absorbency but is normally complete after 24 hours. In some circumstances you may have to wait longer before any other wallcoverings are applied to the Thermal Liner. Check for adhesion before commencing any subsequent redecoration. The adhesive may be used to fill any small gaps at the seams, smooth down using sandpaper before decoration.

Important

  • Do not thin or add water to the adhesive.
  • Contains fungicide and biocide to inhibit mould, yeast and bacteria. Keep away from children and animals. Wash hands thoroughly after use.
  • Do not empty into drains or watercourses. Waste should be disposed of using authorised disposal routes and sites.

This is a simple wallpaper calculator and should be used as a guide only. You can find the roll width and roll length you are after on the specific product page.
Roll widths are provided in meters (such as 0.5 x 10mtr) so your wall widths and heights should be inputted in meters also.
If you are purchasing an offset match product then you may need a little extra as there may be some waste. If you have any windows or doors in your walls you can simply ignore these. This will give a good estimate of required roll numbers.

Wallpaper Calculator